Pumps for pond construction
Here we offer you a wide selection of selected and common pumps for pond construction and pond technology such as Messner pumps, OGM, UP, ORP, submersible pumps, DM-Vario, rinsing pumps for drum filters, Linn tube pumps and much more.
Very powerful submersible pump with cutting device for cutting solid parts (e.g. leaves, thread algae, paper, straw, etc.). Pump housing made of cast iron, shaft made of stainless steel V2A. Ideal for use as a wastewater pump for wastewater from filter systems such as sieve bends and drum filters. Equipped with hose nozzle 50mm and nylon pull cord. Installation max. 5 metres under water. Connection: 2" IT
Die Teichpumpen der AF DM-E Serie sind ideal geeignet für Koi- und Gartenteiche, sowie für den Einsatz in Aquarien. Die Pumpen sind ausgestattet mit der neuesten Technologie der bürstenlosen Permanentmagnetmotoren. Diese Technologie gewährleistet hohe Leistung und geringen Stromverbrauch. Geeignet für nass- und Trockenaufstellung (aber unter dem Wasserspiegel). Geeignet für Filter, Wasserfälle, Wasserläufe, usw. Ein steuerbarer Durchfluss ist möglich mit einem optionalen Controller.
AF EC- Series Pond Pumps Very energy-saving pumps, equipped with innovative electronics! Low-noise function. Equipped with a synchronous motor. No copper parts. Provided with a wear-resistant ceramic shaft. Automatically switches off when there is no water in the rotor. In the event of a blockage from the impeller, the pump sets itself to a blocking position, which means that no further power is consumed until the blockage has been cleared . This is also a dry-running protection and protects the motor. Interesting price/performance ratio of the dirty water pump. Suitable for streams, waterfalls, fountains, filters, etc. Also suitable for dry installation (inlet must be below water level, as not self-priming!). Can pump dirt particles up to 6 mm.
AF EC- Series Pond Pumps Very energy-saving pumps, equipped with innovative electronics! Low-noise function. Equipped with a synchronous motor. No copper parts. Provided with a wear-resistant ceramic shaft. Automatically switches off when there is no water in the rotor. In the event of a blockage from the impeller, the pump sets itself to a blocking position, which means that no further power is consumed until the blockage has been cleared . This is also a dry-running protection and protects the motor. Interesting price/performance ratio of the dirty water pump. Suitable for streams, waterfalls, fountains, filters, etc. Also suitable for dry installation (inlet must be below water level, as not self-priming!). Can pump dirt particles up to 6 mm.
AF EC- Series Pond Pumps Very energy-saving pumps, equipped with innovative electronics! Low-noise function. Equipped with a synchronous motor. No copper parts. Provided with a wear-resistant ceramic shaft. Automatically switches off when there is no water in the rotor. In the event of a blockage from the impeller, the pump sets itself to a blocking position, which means that no further power is consumed until the blockage has been cleared . This is also a dry-running protection and protects the motor. Interesting price/performance ratio of the dirty water pump. Suitable for streams, waterfalls, fountains, filters, etc. Also suitable for dry installation (inlet must be below water level, as not self-priming!). Can pump dirt particles up to 6 mm.
AF EC- Series Pond Pumps Very energy-saving pumps, equipped with innovative electronics! Low-noise function. Equipped with a synchronous motor. No copper parts. Provided with a wear-resistant ceramic shaft. Automatically switches off when there is no water in the rotor. In the event of a blockage from the impeller, the pump sets itself to a blocking position, which means that no further power is consumed until the blockage has been cleared . This is also a dry-running protection and protects the motor. Interesting price/performance ratio of the dirty water pump. Suitable for streams, waterfalls, fountains, filters, etc. Also suitable for dry installation (inlet must be below water level, as not self-priming!). Can pump dirt particles up to 6 mm.
AF EC- Series Pond Pumps Very energy-saving pumps, equipped with innovative electronics! Low-noise function. Equipped with a synchronous motor. No copper parts. Provided with a wear-resistant ceramic shaft. Automatically switches off when there is no water in the rotor. In the event of a blockage from the impeller, the pump sets itself to a blocking position, which means that no further power is consumed until the blockage has been cleared . This is also a dry-running protection and protects the motor. Interesting price/performance ratio of the dirty water pump. Suitable for streams, waterfalls, fountains, filters, etc. Also suitable for dry installation (inlet must be below water level, as not self-priming!). Can pump dirt particles up to 6 mm.
Controller / Regler / Steuerkasten für AF DM-10000 Vario. Bitte beachten Sie, dass dieser Controller NUR für die AF DM-10000 Vario geeignet ist und NICHT für die O-Serie.
Controller / Regler / Steuerkasten für AF DM-22000S Vario. Bitte beachten Sie, dass dieser Controller NUR für die AF DM Vario (S) Serie geeignet ist und NICHT für die O-Serie.
Controller / Regler / Steuerkasten für AF DM-30000 Vario. Bitte beachten Sie, dass dieser Controller NUR für die AF DM-30000 Vario geeignet ist und NICHT für die O-Serie.
Controller für Teichpumpe EASY 40000 l/h
Controller für Teichpumpe OHE 10000VX regelbar
Controller für Teichpumpe OHE 22000VX regelbar
Controller für Teichpumpe OHE 30000VX regelbar
Designed specifically for natural swimming ponds and swimming pools This variable-frequency pump is a safe, high-end product offering excellent performance. To avoid injury and prevent damage to the unit, please read the operating instructions thoroughly. Pump Features 20 adjustable power levels Flow rate correlates with pressure output Display with memory and alarm functions Sine wave technology; ultra-quiet operation Automatic restart after feeding mode Control PanelFunction I. Operating Mode The controller drives the water pump using generated sine wave current. The digital display shows the power output; "PXXX" indicates the pump's operating power. The flow rate is displayed as "1-XX" before automatically switching to the power reading (Watts) after a few seconds. The controller features two operating modes: feeding mode and wave mode. Press the "feeding/wave-making" button to switch between them. Feeding mode displays "1-XX" with a power reading of "P-XXX," while wave mode displays "2-XX," also with a power reading of "P-XXX." Wave mode settings can be adjusted using the "+" and "-" buttons. If an error occurs, press and hold the "feeding/wave-making" button to clear the error code. II. Feeding Mode Briefly press the "feeding/wave-making" button to enter feeding mode settings. The digital display will show "FdXX.XX." This initiates a 10-minute countdown during which the pump stops operating. Once the 10 minutes have elapsed, the pump resumes the previously set operating mode. Briefly press the "feeding/wave-making" button to exit feeding mode. All other buttons are inactive while in feeding mode. III. Display Lock Function When the pump is operating normally, the display locks automatically and shows "LoC". To unlock the display, press and hold the "-" button for approximately 5 seconds. Once unlocked, the display shows "UloC". This function prevents accidental adjustment of the controller settings. IV. Programmable Runtime Press and hold the "+" button to access the operating time settings. The display will show "XXXX", with a default runtime of 6 hours. V. Memory Function The pump does not require reprogramming after a power failure. Upon resuming operation, the device automatically restarts in the last used mode. VI. Error Display and Troubleshooting If the controller detects a fault, the display will flash and show an error code "ErXX". The codes indicate the following: Er01 – Over-voltage protection. Please check that the plug is connected correctly. Er02 – Under-voltage protection. Please check that the plug is connected correctly. Er03 – Short-circuit protection. Please check for cable damage. Er04 – Dry-run protection. Please ensure the pump is connected correctly and not running dry. Er05 – Blockage protection. Please check that the pump is connected correctly and not obstructed by an object. Er06 – Overheating protection. Please ensure the device does not overheat. Resetting the error display: Press the "feeding/wave-making" button while in the error menu to reset the error display. Return the controller to its pre-error state and restart the pump.
Designed specifically for natural swimming ponds and swimming pools This variable-frequency pump is a safe, high-end product offering excellent performance. To avoid injury and prevent damage to the unit, please read the operating instructions thoroughly. Pump Features 20 adjustable power levels Flow rate correlates with pressure output Display with memory and alarm functions Sine wave technology; ultra-quiet operation Automatic restart after feeding mode Control PanelFunction I. Operating Mode The controller drives the water pump using generated sine wave current. The digital display shows the power output; "PXXX" indicates the pump's operating power. The flow rate is displayed as "1-XX" before automatically switching to the power reading (Watts) after a few seconds. The controller features two operating modes: feeding mode and wave mode. Press the "feeding/wave-making" button to switch between them. Feeding mode displays "1-XX" with a power reading of "P-XXX," while wave mode displays "2-XX," also with a power reading of "P-XXX." Wave mode settings can be adjusted using the "+" and "-" buttons. If an error occurs, press and hold the "feeding/wave-making" button to clear the error code. II. Feeding Mode Briefly press the "feeding/wave-making" button to enter feeding mode settings. The digital display will show "FdXX.XX." This initiates a 10-minute countdown during which the pump stops operating. Once the 10 minutes have elapsed, the pump resumes the previously set operating mode. Briefly press the "feeding/wave-making" button to exit feeding mode. All other buttons are inactive while in feeding mode. III. Display Lock Function When the pump is operating normally, the display locks automatically and shows "LoC". To unlock the display, press and hold the "-" button for approximately 5 seconds. Once unlocked, the display shows "UloC". This function prevents accidental adjustment of the controller settings. IV. Programmable Runtime Press and hold the "+" button to access the operating time settings. The display will show "XXXX", with a default runtime of 6 hours. V. Memory Function The pump does not require reprogramming after a power failure. Upon resuming operation, the device automatically restarts in the last used mode. VI. Error Display and Troubleshooting If the controller detects a fault, the display will flash and show an error code "ErXX". The codes indicate the following: Er01 – Over-voltage protection. Please check that the plug is connected correctly. Er02 – Under-voltage protection. Please check that the plug is connected correctly. Er03 – Short-circuit protection. Please check for cable damage. Er04 – Dry-run protection. Please ensure the pump is connected correctly and not running dry. Er05 – Blockage protection. Please check that the pump is connected correctly and not obstructed by an object. Er06 – Overheating protection. Please ensure the device does not overheat. Resetting the error display: Press the "feeding/wave-making" button while in the error menu to reset the error display. Return the controller to its pre-error state and restart the pump.
Speziell für Schwimmteiche und SwimmingpoolsDie variable Frequenzpumpe ist ein sicheres Highend Produkt mit guter Performance. Um unnötige Verletzungen zu vermeiden und Schäden am Gerät zu verhindern lesen Sie bitte ausführlich die Betriebsanleitung. Eigenschaften der Pumpe20 einstellbare LeistungsstufenDie Durchflussmenge erhöht den DruckFunktionsdisplay mit Memory und AlarmSinuswelle, Ultra leiseAutomatischer Start, nach FütterungsmodusControl PanelFunktionI. ArbeitsmodusDer Controller treibt die Wasserpumpe durch den erzeugten Sinusstrom an. Auf der Digitalen Anzeige wird die Leistung angezeigt „PXXX, XXX“ zeigt die Leistung der Pumpe im Betrieb an. Die Durchflussrate wird als „1-XX“ angezeigt, und wird automatisch nach wenigen Sekunden zu Leistung wechseln (Watt).Der Controller hat 2 Arbeitsmodi: den Futtermodus und den Wellenmodus. Drücken Sie den „feeding/wave-making“ Knopf um in den jeweiligen Modus zu wechseln. Der Futtermodus zeigt „1-XX“ an mit einer Watt Angabe von „P-XXX“ und der Wellenmodus zeigt „2-XX“ an ebenfalls mit einer Watt Angabe von „P-XXX“. Der Wellenmodus kann reguliert werden mit den „+“ und „-“ Tasten.Falls ein Fehler auftreten sollte, halten Sie den „feeding/wave-making“ Knopf für eine längere Zeit gedrückt, um den Fehlercode zu löschen.II. FuttermodusDrücken Sie den „feeding/wave-making“ Knopf kurz, um in die Einstellung des Futtermodus zu gelangen. Dann zeigt die Digitalanzeige „FdXX.XX“ an. Dies ist ein 10 Minuten Countdown in welchem die Pumpe den Betrieb stoppt solange der Futtermodus aktiv ist. Nach Ablauf der 10 Minuten wird die Pumpe wieder in den Betrieb wechseln, welcher zuvor eingestellt wurde. Drücken Sie den „feeding/wave-making“ Knopf kurz, um den Futtermodus zu verlassen. Alle anderen Knöpfe haben im Futtermodus keine Funktion.III. Sperrfunktion vom DisplayWenn die Pumpe im normal Betrieb läuft, ist das Display automatisch gesperrt und zeigt „LoC“ an. Um das Display zu entsperren halten Sie die „-“ Taste ca. 5 Sekunden lang gedrückt. Nachdem das Display entsperrt wurde zeigt das Display „UloC“ an. Diese Funktion verhindert, dass der Kontroller durch aus Versehen verstellt wird. IV. Programmierbare LaufzeitHalten Sie die „+“ Taste gedrückt um in die Einstellung für die Betriebszeit zu gelangen. Auf dem Display erscheint nun „XXXX“ mit 6 Stunden als einer Laufzeit.V. Einstellung ErinnerungsfunktionBei Stromausfall muss die Pumpe nicht erneut programmiert werden. Bei wieder Aufnahme des Betriebes wird das Gerät automatisch den zuletzt verwendeten Modus wieder starten.VI. Fehler Anzeige und BehebungWenn der Kontroller einen Fehler anzeigt, wird er aufblinken und ein Fehlercode „ErXX“ wird angezeigt. Die Codes haben folgende Bedeutung:Er01 – Überspannungsschutz. Bitte überprüfen Sie, ob der Stecker korrekt angeschlossen ist.Er02 – Unterspannungsschutz. Bitte überprüfen Sie, ob der Stecker korrekt angeschlossen ist.Er03 – Kurzschlussschutz. Bitte überprüfen Sie, ob das Kabel beschädigt ist.Er04 – Leerlaufschutz. Bitte achten Sie darauf, dass die Pumpe korrekt angeschlossen ist oder trocken läuft.Er05 – Blockierschutz. Bitte überprüfen Sie, ob die Pumpe korrekt angeschlossen ist oder durch einen Gegenstand blockiert wird.Er06 – Überhitzungsschutz. Bitte stellen Sie sicher dass das Gerät nicht heiß läuft.Fehleranzeige zurücksetzen: Drücken Sie den „feeding/wave-making“ Knopf im Fehlermenü um die Fehleranzeige zurück zu setzen. Versetzen Sie den Kontroller zurück auf den Stand vor der Fehleranzeige und starten Sie die Pumpe neu.
Technical data: - Dry-running protection- low energy consumption- for fresh and salt water- also suitable for dry installation (inlet must be below water level, as not self-priming!).- can pump dirt particles up to 6 mm- Voltage: 220-240 V 50 Hz- Pmax.: 360 watts- Threaded connection: 2.5"/2.5"- Hose connection 3/4", 1", 1 1/4", 1 1/2"- Qmax: 40,000 L/h- Hmax: 9 m- with 6m rubber cable and waterproof controller box- Dimensions: 240 mm x 390 mm x 216 mm- Weight: 7.0 kg
Highly efficient continuous running pumps with asynchronous motors. Optimised design for pumping large volumes of water over smaller height differences with the lowest possible power consumption, e.g. for: - Pond filters- Waterfalls- Brooks Operation on power controller ODR-800 possible. Further features: - transports dirt particles up to 6 mm in diameter without clogging- drive of the rotor via a long-life ceramic shaft- suitable for freshwater only
Highly efficient continuous running pumps with asynchronous motors. Optimised design for pumping large volumes of water over smaller height differences with the lowest possible power consumption, e.g. for: - Pond filters- Waterfalls- Brooks Operation on power controller ODR-800 possible. Further features: - transports dirt particles up to 6 mm in diameter without clogging- drive of the rotor via a long-life ceramic shaft- suitable for freshwater only
Highly efficient continuous running pumps with asynchronous motors. Optimised design for pumping large volumes of water over smaller height differences with the lowest possible power consumption, e.g. for: - Pond filters- Waterfalls- Brooks Operation on power controller ODR-800 possible. Further features: - transports dirt particles up to 6 mm in diameter without clogging- drive of the rotor via a long-life ceramic shaft- suitable for freshwater only
Ersatz- Rotor / Flügelrad für HAILEA HX-6520
Ersatz- Rotor / Flügelrad für HAILEA HX-6530
Ersatz- Rotor / Flügelrad für HAILEA HX-6540