CL drum filter

Function The function of the drum filter is to filter polluted water mechanically. Smallest particles are separated from the water by a stainless steel sieve RVS 316 of 75 micrometres and led to the outside via a dirt drain. This filtering process is automatically regulated by a control system and monitored by probes. In the event of a malfunction, the filter automatically switches off the circulation and backwash pump. The water level is constantly monitored by probes. The EPS Combi Drum Filter CL35 is made of very high quality PP plastic and is supplied including control, emergency cover switch, manual channel flushing, complete piping from the flushing pump to the flushing channel, level regulator, cover and built-in flushing pump in an unprecedented price/performance ratio. All inclusive. All EPS drum filters are reinforced with a 50/50 U-profile and an inner core of 40/40 4 Kant steel pipe. The direct drive from the motor to the drum means that there are no wear parts as with conventional drum filters (V-belts, toothed belts or plastic gears). If the waste water channel should ever become clogged due to strong filamentous algae or leaves, it is no problem to simply dismantle and clean it without having to remove the filter drum or the fabric. In the integrated biochamber (102 x 67 x 98 cm), a Japanese air hose ( 19 mm ) is directly pre-installed for a better "moving bed" process for improved turbulence of the HX 13/17. This requires a diaphragm pump of 100-120 L/min. We recommend either the HAP series, the Secoh series or the AP series. In addition, the biochamber has been equipped with 8mm slots to insert HX13/17.  Please note the protected and unprotected surface for the HX13/17. According to this, the square metre of bacteria removal surface is calculated. The CL35 drum filter is available in both pump and gravity versions. Even if you have a gravity version, it is possible to convert it to a pump version in just a few steps (if you need help with this, we will be happy to assist you). Instructions for the conversion are enclosed with the control box. The fuse function or the emergency lid switch switches off the immersion UVCs directly when the lid is opened. The function is only guaranteed if they are connected via the supplied control unit. It is recommended that the electrical connection of the control unit is protected by a residual current circuit breaker. The control unit should not be directly exposed to moisture. Suitable connection accessories would be elastomer sleeve 110mm, elastomer end caps 110mm (if you do not need all inlets and outlets). As UV lamp we recommend our submersible UVC 40W Amalgan or submersible UVC 80W Amalgam. By using deep well pumps a flushing process is hardly audible. Additional options - different filter panels (filter meshes) in stainless steel RVS available on order and at extra charge in 43µ or 60µ (please note that with finer meshes the flow rate is 30% to 50% lower depending on the µ-thickness) - our EPS drum filters can be built individually according to drawing at extra charge - individual biochambers (round or square) as well as trickle filters can be built on request in all sizes according to drawing - if you would like individual advice, please feel free to call us on 02945 / 96950 Functions of the control system: - Plug location for circulation and rinsing pump - Plug and Play via a sensor with measuring pins  - automatic cleaning - switch for on/off incl. emergency switch - Button for manual flushing - Flushing is triggered by probes (level of probes adjustable) - Rotation time/flush time adjustable - CE mark - detailed instructions for use are included - Cleaning is adjustable ( time and duration ) - Dry-running protection for the pond pump - Dry-running protection for circulation and flushing pump - Connections for sensor and safety switch Why EPS drum filters? after 30 years of experience and many purchased and self-tested filter systems from different suppliers, we decided to build our own drum filter series. There are stainless steel, PE and PP drum filters on the market. Some of the stainless steel filters were notable for their poor workmanship (cheap tank connectors that leaked, broke off or had rust defects). PE filters caused big problems when exposed to sunlight (bending and warping of the material) Many drum filters do not have a direct drive and are driven by pinions, V-belts or toothed belts. In our opinion, these are all weak points that can lead to malfunctions. For these reasons, we decided to build PP filters that do not deform, are acid-resistant and are operated with a direct drive. After an intensive test period of approx. 6 years in our own KOI facility, which consists of approx. 60 tanks of various sizes, with full fish stocking and abundant feeding every day, we started series production. All the above problems are now a thing of the past - We love clear water and healthy fish EPS drum filters reduce the need for cleaning and maintenance in fish farms and garden ponds to a minimum. The processing is carried out using the latest technology such as CNC machines, which guarantees quality and precision. The systems can be used in the koi and/or swimming pond sector as well as in fish farming, industry and public areas.Dispatch by one-way pallet 220x100x80NEW: Water-saving function via the intelligent controlThe new control is preset with a water-saving function ex works, whereby the drum rotates half a revolution without rinsing at the first contact with the probes. At the second contact on the probes, the drum is rotated a full revolution and cleaned completely. This reduces electricity and water consumption. You can see the quality for yourself at any time in our showroom. We look forward to your visit

Function The function of the drum filter is to filter polluted water mechanically. Smallest particles are separated from the water by a stainless steel sieve RVS 316 of 75 micrometres and led to the outside via a dirt drain. This filtering process is automatically regulated by a control system and monitored by probes. In the event of a malfunction, the filter automatically switches off the circulation and backwash pump. The water level is constantly monitored by probes. The EPS Combi Drum Filter CL35 is made of very high quality PP plastic and is supplied including control, emergency cover switch, manual channel flushing, complete piping from the flushing pump to the flushing channel, level regulator, cover and built-in flushing pump in an unprecedented price/performance ratio. All inclusive. All EPS drum filters are reinforced with a 50/50 U-profile and an inner core of 40/40 4 Kant steel pipe. The direct drive from the motor to the drum means that there are no wear parts as with conventional drum filters (V-belts, toothed belts or plastic gears). If the waste water channel should ever become clogged due to strong filamentous algae or leaves, it is no problem to simply dismantle and clean it without having to remove the filter drum or the fabric. In the integrated biochamber (102 x 67 x 98 cm), a Japanese air hose ( 19 mm ) is directly pre-installed for a better "moving bed" process for improved turbulence of the HX 13/17. This requires a diaphragm pump of 100-120 L/min. We recommend either the HAP series, the Secoh series or the AP series. In addition, the biochamber has been equipped with 8mm slots to insert HX13/17.  Please note the protected and unprotected surface for the HX13/17. According to this, the square metre of bacteria removal surface is calculated. The CL35 drum filter is available in both pump and gravity versions. Even if you have a gravity version, it is possible to convert it to a pump version in just a few steps (if you need help with this, we will be happy to assist you). Instructions for the conversion are enclosed with the control box. The fuse function or the emergency lid switch switches off the immersion UVCs directly when the lid is opened. The function is only guaranteed if they are connected via the supplied control unit. It is recommended that the electrical connection of the control unit is protected by a residual current circuit breaker. The control unit should not be directly exposed to moisture. Suitable connection accessories would be elastomer sleeve 110mm, elastomer end caps 110mm (if you do not need all inlets and outlets). As UV lamp we recommend our submersible UVC 40W Amalgan or submersible UVC 80W Amalgam. By using deep well pumps a flushing process is hardly audible. Additional options - different filter panels (filter meshes) in stainless steel RVS available on order and at extra charge in 43µ or 60µ (please note that with finer meshes the flow rate is 30% to 50% lower depending on the µ-thickness) - our EPS drum filters can be built individually according to drawing at extra charge - individual biochambers (round or square) as well as trickle filters can be built on request in all sizes according to drawing - if you would like individual advice, please feel free to call us on 02945 / 96950 Functions of the control system: - Plug location for circulation and rinsing pump - Plug and Play via a sensor with measuring pins  - automatic cleaning - switch for on/off incl. emergency switch - Button for manual flushing - Flushing is triggered by probes (level of probes adjustable) - Rotation time/flush time adjustable - CE mark - detailed instructions for use are included - Cleaning is adjustable ( time and duration ) - Dry-running protection for the pond pump - Dry-running protection for circulation and flushing pump - Connections for sensor and safety switch Why EPS drum filters? after 30 years of experience and many purchased and self-tested filter systems from different suppliers, we decided to build our own drum filter series. There are stainless steel, PE and PP drum filters on the market. Some of the stainless steel filters were notable for their poor workmanship (cheap tank connectors that leaked, broke off or had rust defects). PE filters caused big problems when exposed to sunlight (bending and warping of the material) Many drum filters do not have a direct drive and are driven by pinions, V-belts or toothed belts. In our opinion, these are all weak points that can lead to malfunctions. For these reasons, we decided to build PP filters that do not deform, are acid-resistant and are operated with a direct drive. After an intensive test period of approx. 6 years in our own KOI facility, which consists of approx. 60 tanks of various sizes, with full fish stocking and abundant feeding every day, we started series production. All the above problems are now a thing of the past - We love clear water and healthy fish EPS drum filters reduce the need for cleaning and maintenance in fish farms and garden ponds to a minimum. The processing is carried out using the latest technology such as CNC machines, which guarantees quality and precision. The systems can be used in the koi and/or swimming pond sector as well as in fish farming, industry and public areas.Dispatch by one-way pallet 220x100x80NEW: Water-saving function via the intelligent controlThe new control is preset with a water-saving function ex works, whereby the drum rotates half a revolution without rinsing at the first contact with the probes. At the second contact on the probes, the drum is rotated a full revolution and cleaned completely. This reduces electricity and water consumption. You can see the quality for yourself at any time in our showroom. We look forward to your visit

Function The function of the drum filter is to filter polluted water mechanically. Smallest particles are separated from the water by a stainless steel sieve RVS 316 of 75 micrometres and led to the outside via a dirt drain. This filtering process is automatically regulated by a control system and monitored by probes. In the event of a malfunction, the filter automatically switches off the circulation and backwash pump. The water level is constantly monitored by probes. The EPS Combi Drum Filter CL35 is made of very high quality PP plastic and is supplied including control, emergency cover switch, manual channel flushing, complete piping from the flushing pump to the flushing channel, level regulator, cover and built-in flushing pump in an unprecedented price/performance ratio. All inclusive. All EPS drum filters are reinforced with a 50/50 U-profile and an inner core of 40/40 4 Kant steel pipe. The direct drive from the motor to the drum means that there are no wear parts as with conventional drum filters (V-belts, toothed belts or plastic gears). If the waste water channel should ever become clogged due to strong filamentous algae or leaves, it is no problem to simply dismantle and clean it without having to remove the filter drum or the fabric. In the integrated biochamber (102 x 67 x 98 cm), a Japanese air hose ( 19 mm ) is directly pre-installed for a better "moving bed" process for improved turbulence of the HX 13/17. This requires a diaphragm pump of 100-120 L/min. We recommend either the HAP series, the Secoh series or the AP series. In addition, the biochamber has been equipped with 8mm slots to insert HX13/17.  Please note the protected and unprotected surface for the HX13/17. According to this, the square metre of bacteria removal surface is calculated. The CL35 drum filter is available in both pump and gravity versions. Even if you have a gravity version, it is possible to convert it to a pump version in just a few steps (if you need help with this, we will be happy to assist you). Instructions for the conversion are enclosed with the control box. The fuse function or the emergency lid switch switches off the immersion UVCs directly when the lid is opened. The function is only guaranteed if they are connected via the supplied control unit. It is recommended that the electrical connection of the control unit is protected by a residual current circuit breaker. The control unit should not be directly exposed to moisture. Suitable connection accessories would be elastomer sleeve 110mm, elastomer end caps 110mm (if you do not need all inlets and outlets). As UV lamp we recommend our submersible UVC 40W Amalgan or submersible UVC 80W Amalgam. By using deep well pumps a flushing process is hardly audible. Additional options - different filter panels (filter meshes) in stainless steel RVS available on order and at extra charge in 43µ or 60µ (please note that with finer meshes the flow rate is 30% to 50% lower depending on the µ-thickness) - our EPS drum filters can be built individually according to drawing at extra charge - individual biochambers (round or square) as well as trickle filters can be built on request in all sizes according to drawing - if you would like individual advice, please feel free to call us on 02945 / 96950 Functions of the control system: - Plug location for circulation and rinsing pump - Plug and Play via a sensor with measuring pins  - automatic cleaning - switch for on/off incl. emergency switch - Button for manual flushing - Flushing is triggered by probes (level of probes adjustable) - Rotation time/flush time adjustable - CE mark - detailed instructions for use are included - Cleaning is adjustable ( time and duration ) - Dry-running protection for the pond pump - Dry-running protection for circulation and flushing pump - Connections for sensor and safety switch Why EPS drum filters? after 30 years of experience and many purchased and self-tested filter systems from different suppliers, we decided to build our own drum filter series. There are stainless steel, PE and PP drum filters on the market. Some of the stainless steel filters were notable for their poor workmanship (cheap tank connectors that leaked, broke off or had rust defects). PE filters caused big problems when exposed to sunlight (bending and warping of the material) Many drum filters do not have a direct drive and are driven by pinions, V-belts or toothed belts. In our opinion, these are all weak points that can lead to malfunctions. For these reasons, we decided to build PP filters that do not deform, are acid-resistant and are operated with a direct drive. After an intensive test period of approx. 6 years in our own KOI facility, which consists of approx. 60 tanks of various sizes, with full fish stocking and abundant feeding every day, we started series production. All the above problems are now a thing of the past - We love clear water and healthy fish EPS drum filters reduce the need for cleaning and maintenance in fish farms and garden ponds to a minimum. The processing is carried out using the latest technology such as CNC machines, which guarantees quality and precision. The systems can be used in the koi and/or swimming pond sector as well as in fish farming, industry and public areas.Dispatch by one-way pallet 220x100x80NEW: Water-saving function via the intelligent controlThe new control is preset with a water-saving function ex works, whereby the drum rotates half a revolution without rinsing at the first contact with the probes. At the second contact on the probes, the drum is rotated a full revolution and cleaned completely. This reduces electricity and water consumption. You can see the quality for yourself at any time in our showroom. We look forward to your visit

Function The function of the drum filter is to filter polluted water mechanically. Smallest particles are separated from the water by a stainless steel sieve RVS 316 of 75 micrometres and led to the outside via a dirt drain. This filtering process is automatically regulated by a control system and monitored by probes. In the event of a malfunction, the filter automatically switches off the circulation and backwash pump. The water level is constantly monitored by probes. The EPS Combi Drum Filter CL35 is made of very high quality PP plastic and is supplied including control, emergency cover switch, manual channel flushing, complete piping from the flushing pump to the flushing channel, level regulator, cover and built-in flushing pump in an unprecedented price/performance ratio. All inclusive. All EPS drum filters are reinforced with a 50/50 U-profile and an inner core of 40/40 4 Kant steel pipe. The direct drive from the motor to the drum means that there are no wear parts as with conventional drum filters (V-belts, toothed belts or plastic gears). If the waste water channel should ever become clogged due to strong filamentous algae or leaves, it is no problem to simply dismantle and clean it without having to remove the filter drum or the fabric. In the integrated biochamber (102 x 67 x 98 cm), a Japanese air hose ( 19 mm ) is directly pre-installed for a better "moving bed" process for improved turbulence of the HX 13/17. This requires a diaphragm pump of 100-120 L/min. We recommend either the HAP series, the Secoh series or the AP series. In addition, the biochamber has been equipped with 8mm slots to insert HX13/17.  Please note the protected and unprotected surface for the HX13/17. According to this, the square metre of bacteria removal surface is calculated. The CL35 drum filter is available in both pump and gravity versions. Even if you have a gravity version, it is possible to convert it to a pump version in just a few steps (if you need help with this, we will be happy to assist you). Instructions for the conversion are enclosed with the control box. The fuse function or the emergency lid switch switches off the immersion UVCs directly when the lid is opened. The function is only guaranteed if they are connected via the supplied control unit. It is recommended that the electrical connection of the control unit is protected by a residual current circuit breaker. The control unit should not be directly exposed to moisture. Suitable connection accessories would be elastomer sleeve 110mm, elastomer end caps 110mm (if you do not need all inlets and outlets). As UV lamp we recommend our submersible UVC 40W Amalgan or submersible UVC 80W Amalgam. By using deep well pumps a flushing process is hardly audible. Additional options - different filter panels (filter meshes) in stainless steel RVS available on order and at extra charge in 43µ or 60µ (please note that with finer meshes the flow rate is 30% to 50% lower depending on the µ-thickness) - our EPS drum filters can be built individually according to drawing at extra charge - individual biochambers (round or square) as well as trickle filters can be built on request in all sizes according to drawing - if you would like individual advice, please feel free to call us on 02945 / 96950 Functions of the control system: - Plug location for circulation and rinsing pump - Plug and Play via a sensor with measuring pins  - automatic cleaning - switch for on/off incl. emergency switch - Button for manual flushing - Flushing is triggered by probes (level of probes adjustable) - Rotation time/flush time adjustable - CE mark - detailed instructions for use are included - Cleaning is adjustable ( time and duration ) - Dry-running protection for the pond pump - Dry-running protection for circulation and flushing pump - Connections for sensor and safety switch Why EPS drum filters? after 30 years of experience and many purchased and self-tested filter systems from different suppliers, we decided to build our own drum filter series. There are stainless steel, PE and PP drum filters on the market. Some of the stainless steel filters were notable for their poor workmanship (cheap tank connectors that leaked, broke off or had rust defects). PE filters caused big problems when exposed to sunlight (bending and warping of the material) Many drum filters do not have a direct drive and are driven by pinions, V-belts or toothed belts. In our opinion, these are all weak points that can lead to malfunctions. For these reasons, we decided to build PP filters that do not deform, are acid-resistant and are operated with a direct drive. After an intensive test period of approx. 6 years in our own KOI facility, which consists of approx. 60 tanks of various sizes, with full fish stocking and abundant feeding every day, we started series production. All the above problems are now a thing of the past - We love clear water and healthy fish EPS drum filters reduce the need for cleaning and maintenance in fish farms and garden ponds to a minimum. The processing is carried out using the latest technology such as CNC machines, which guarantees quality and precision. The systems can be used in the koi and/or swimming pond sector as well as in fish farming, industry and public areas.Dispatch by one-way pallet 220x100x80NEW: Water-saving function via the intelligent controlThe new control is preset with a water-saving function ex works, whereby the drum rotates half a revolution without rinsing at the first contact with the probes. At the second contact on the probes, the drum is rotated a full revolution and cleaned completely. This reduces electricity and water consumption. You can see the quality for yourself at any time in our showroom. We look forward to your visit

Function The function of the drum filter is to filter polluted water mechanically. Smallest particles are separated from the water by a stainless steel sieve RVS 316 of 75 micrometres and led to the outside via a dirt drain. This filtering process is automatically regulated by a control system and monitored by probes. In the event of a malfunction, the filter automatically switches off the circulation and backwash pump. The water level is constantly monitored by probes. The EPS Combi Drum Filter CL65 is made of very high quality PP plastic and is supplied including control, emergency cover switch, manual channel flushing, complete piping from the flushing pump to the flushing channel, level control, cover and built-in flushing pump in an unprecedented price/performance ratio. All EPS drum filters are reinforced with a 50/50 U-profile and an inner core of 40/40 4 Kant steel pipe. The direct drive from the motor to the drum eliminates the need for wear parts such as V-belts, toothed belts or plastic gears found in conventional drum filters. If the dirty water channel should ever become clogged due to strong filamentous algae or leaves, it is no problem to simply dismantle and clean it without having to dismantle the filter drum or remove the mesh. In the integrated biochamber (102 x 98 x 97 cm), a Japanese air hose (19 mm) is directly pre-installed for a better "moving bed" process for improved turbulence of the HX 13/17. This requires a diaphragm pump of 100-120 L/min. We recommend either HAP series, the Secoh series or the AP series. In addition, the biochamber has been equipped with 8mm slots to insert HX13/17.  Please note the protected and unprotected surface of the HX13/17. According to this, the square metre of bacteria removal surface is calculated. The CL65 drum filter is available in both pump and gravity versions. Even if you have a gravity version, it is possible to convert it to a pump version in just a few steps (if you need help with this, we will be happy to assist you). Instructions for the conversion are enclosed with the control box. The fuse function or the emergency lid switch switches off the immersion UVCs directly when the lid is opened. The function is only guaranteed if they are connected via the supplied control unit. It is recommended that the electrical connection of the control unit is protected by a residual current circuit breaker. The control unit should not be directly exposed to moisture. Suitable connection accessories would be Elastomer sleeve 110mm, Elastomer end caps 110mm (if you do not need all inlets and outlets). As UV lamp we recommend our submersible UVC 40W Amalgan or Immersion UVC 80W Amalgam. Due to the use of deep well pumps, a flushing process is hardly audible. Additional options - different filter panels (filter mesh) in stainless steel RVS available to order and at extra cost in 43µ or 60µ (please note that with finer mesh the flow rate is 30% to 50% lower depending on the µ-thickness) - our EPS drum filters can be built individually on request according to drawings at an extra charge - individual biochambers (round or square) as well as trickle filters can be built on request in all sizes according to drawing - if you would like individual advice, please feel free to call us on 02945 / 96950 Functions of the control system: - Plug place for circulation and rinsing pump - plug and play via sensor with measuring pins  - automatic cleaning - Switch for on/off incl. emergency switch - Button for manual flushing - Flushing is triggered by probes (level of probes adjustable) - Rotation time/flush time adjustable - CE mark - detailed instructions for use are included - Cleaning is adjustable ( time and duration ) - Dry-running protection for the pond pump - Dry-running protection for circulation and flushing pump - Connections for sensor and safety switch Why EPS drum filters? after 30 years of experience and many purchased and self-tested filter systems from different suppliers, we decided to build our own drum filter series. There are stainless steel, PE and PP drum filters on the market. Some of the stainless steel filters were notable for their poor workmanship (cheap tank connectors that leaked, broke off or had rust defects). PE filters caused big problems when exposed to sunlight (bending and warping of the material) Many drum filters do not have a direct drive and are driven by pinions, V-belts or toothed belts. The use of salt also became problematic. In our view, these are all weak points that can lead to malfunctions. For these reasons, we decided to build PP filters that do not deform, are acid-resistant and are operated with a direct drive. After an intensive test period of approx. 1.5 years in our own KOI facility, which consists of approx. 60 tanks of various sizes, with full fish stocking and abundant feeding every day, we started series production. All these problems are now a thing of the past - We love clear water and healthy fish EPS drum filters reduce the need for cleaning and maintenance in fish farms and garden ponds to a minimum. The processing is carried out using the latest technology such as CNC machines, which guarantees quality and precision. The systems can be used in the koi and/or swimming pond sector as well as in fish farming, industry and public areas.Dispatch by one-way pallet 220x100x80Technical data:EPS Combi Drum Filter CL65NEW: Water saving function via the intelligent control- the new control is pre-set with a water saving function ex works, whereby the first contact at the probes causes the drum to rotate half a turn without rinsing. At the second contact on the probes, the drum is rotated a full revolution and cleaned completely. This reduces electricity and water consumption- maximum flow rate with gravity: 65 m³ / hr. (with pumped version -30% pump capacity)- Dimensions: 205 x 97 x 98 cm- Material: PP 10 - 15mm and 2 mm stainless steel drum- Installation height with gravity: 13 cm above water- Water volume biochamber: approx. 970 L- Volume biomedium: approx. 350 - 450 L- Number of inlets: 6 x 110 mm- Number of outlets: 7 x 110 mm- Dirty water outlet: 1 x 110 mm- Flushing pump: EPS750- Weight: approx. 100 kg- Noise level: < 70 db- Mains voltage: 230V / 50 Hz- Removable nozzle assembly- Unscrewable flushing channel - Incl. manual channel flushing with ball valve- 2x 90 mm drum bypass- Incl. six sockets (1x drum motor, 1x flushing pump, 3x pond pump, 1x 230V for second pond pump or UVC)- Direct drive from motor to drum- Built-in Japanese 19mm air hose for better movement of the biomedium (Helix)- Connection for air hose 20 mm (other sizes individually possible)- Stainless steel filter panel- Stainless steel mesh 75 micron RVS 316- Flushing times adjustable- Drive motor 220V 50NM- Incl. Emergency cover switch- incl. control unit and measuring probes- maintenance key for specialised trade- cover in 2 parts is part of the delivery- operating instructions as well as control unit instructions are included in the delivery- conversion from gravity to pump version is possible in just a few steps ( conversion instructions in the control unit box )- guarantee: 2 years (the stainless steel sieve is a wearing part and excluded from the guarantee)- payment by instalments via PayPal possible You can convince yourself of the quality at any time in our showroom We look forward to your visit

InnovationsDue to the high demand, we have now designed a CL65 transverse where the inlets and outlets can all be operated from one side (from the front).This filter is available in 2 versions, one drum on the left and one drum on the right.Due to this diversity, our CL drum filters can be installed in any filter chamber without any problems.This filter does not have a baffle for the biomaterial to the outlet.Please do not hesitate to contact us if you have any questions.Function:The function of the drum filter is to filter polluted water mechanically. Smallest particles are separated from the water by a stainless steel sieve RVS 316 of 75 micrometres and led to the outside via a dirt drain. This filtering process is automatically regulated by a control system and monitored by probes. In the event of a malfunction, the filter automatically switches off the circulation and backwash pump. The water level is constantly monitored by probes. The EPS Combi Drum Filter CL65 is made of very high quality PP plastic and is supplied including control, emergency cover switch, manual channel flushing, complete piping from the flushing pump to the flushing channel, level regulator, cover and built-in flushing pump in an unprecedented price/performance ratio. All EPS drum filters are reinforced with a 50/50 U-profile and an inner core of 40/40 4 Kant steel pipe. The direct drive from the motor to the drum eliminates the need for wear parts such as V-belts, toothed belts or plastic gears found in conventional drum filters. If the dirty water channel should ever become clogged due to strong filamentous algae or leaves, it is no problem to simply dismantle and clean it without having to dismantle the filter drum or remove the mesh. In the integrated biochamber (105 x 87 x 97 cm), a Japanese air hose (19 mm) is directly pre-installed for a better "moving bed" process for improved turbulence of the HX 13/17. This requires a diaphragm pump of 100-120 L/min. We recommend either HAP series, the Secoh series or the AP series. Please note the protected and unprotected surface for the HX13/17. Then the square metre of bacteria removal area is calculated. The CL65 drum filter is available in both pump and gravity versions. Even if you have a gravity version, it is possible to convert it to a pump version in just a few steps (if you need help with this, we will be happy to assist you). Instructions for the conversion are enclosed with the control box. The fuse function or the emergency lid switch switches off the immersion UVCs directly when the lid is opened. The function is only guaranteed if they are connected via the supplied control unit. It is recommended that the electrical connection of the control unit is protected by a residual current circuit breaker. The control unit should not be directly exposed to moisture. Suitable connection accessories would be Elastomer sleeve 110mm, Elastomer end caps 110mm (if you do not need all inlets and outlets). As UV lamp we recommend our submersible UVC 40W Amalgan or Immersion UVC 80W Amalgam. Due to the use of deep well pumps, a flushing process is hardly audible. Additional options - different filter panels (filter mesh) in stainless steel RVS available to order and at extra cost in 43µ or 60µ (please note that with finer mesh the flow rate is 30% to 50% lower depending on the µ-thickness) - our EPS drum filters can be built individually according to drawing at extra charge - individual biochambers (round or square) as well as trickle filters can be built on request in all sizes according to drawings Functions of the control system: - Plug place for circulation and rinsing pump- Plug and Play via a sensor with measuring pins - automatic cleaning- Switch for on/off incl. emergency switch- Button for manual rinsing- The rinses are triggered by probes (level of the probes adjustable)- Rotation time/rinsing time adjustable- detailed operating instructions are included- Cleaning is adjustable ( time and duration )- Dry run protection for the pond pump- Dry run protection for circulation and rinsing pump- Connections for probes and safety showers Why EPS drum filters? after 30 years of experience and many purchased and self-tested filter systems from different suppliers, we decided to build our own drum filter series. There are stainless steel, PE and PP drum filters on the market. Some of the stainless steel filters were notable for their poor workmanship (cheap tank connectors that leaked, broke off or had rust defects). PE filters caused big problems when exposed to sunlight (bending and warping of the material) Many drum filters do not have a direct drive and are driven by pinions, V-belts or toothed belts. The use of salt also became problematic. In our view, these are all weak points that can lead to malfunctions. For these reasons, we decided to build PP filters that do not deform, are acid-resistant and are operated with a direct drive. After an intensive test period of approx. 6 years in our own KOI facility, which consists of approx. 60 tanks of various sizes, with full fish stocking and abundant feeding every day, we started series production. All these problems are now a thing of the past - We love clear water and healthy fish EPS drum filters reduce the need for cleaning and maintenance in fish farms and garden ponds to a minimum. The processing is carried out using the latest technology such as CNC machines, which guarantees quality and precision. The systems can be used in the koi and/or swimming pond sector as well as in fish farming, industry and public areas.Dispatch by one-way pallet 220x100x80You can convince yourself of the quality at any time in our exhibition We look forward to your visit

Function The function of the drum filter is to filter polluted water mechanically. Smallest particles are separated from the water by a stainless steel sieve RVS 316 of 75 micrometres and led to the outside via a dirt drain. This filtering process is automatically regulated by a control system and monitored by probes. In the event of a malfunction, the filter automatically switches off the circulation and backwash pump. The water level is constantly monitored by probes. The EPS Combi Drum Filter CL65 is made of very high quality PP plastic and is supplied including control, emergency cover switch, manual channel flushing, complete piping from the flushing pump to the flushing channel, level regulator, cover and built-in flushing pump in an unprecedented price/performance ratio. All inclusive. All EPS drum filters are reinforced with a 50/50 U-profile and an inner core of 40/40 4 Kant steel pipe. The direct drive from the motor to the drum means that there are no wear parts as with conventional drum filters (V-belts, toothed belts or plastic gears). If the dirty water channel should ever become clogged due to strong filamentous algae or leaves, it is no problem to simply dismantle and clean it without having to dismantle the filter drum or remove the mesh. In the integrated biochamber (102 x 98 x 97 cm) a Japanese air hose ( 19 mm ) is directly pre-installed for a better "moving bed" process for improved turbulence of the HX 13/17. This requires a diaphragm pump of 100-120 L/min. We recommend either HAP series, the Secoh series or the AP series. In addition, the biochamber has been equipped with 8 mm slots to insert HX13/17.  Please note the protected and unprotected surface of the HX13/17. According to this, the square metre of bacteria removal surface is calculated. The CL65 drum filter is available in both pump and gravity versions. Even if you have a gravity version, it is possible to convert it to a pump version in just a few steps (if you need help with this, we will be happy to assist you). Instructions for the conversion are enclosed with the control box. The fuse function or the emergency lid switch switches off the immersion UVCs directly when the lid is opened. The function is only guaranteed if they are connected via the supplied control unit. It is recommended that the electrical connection of the control unit is protected by a residual current circuit breaker. The control unit should not be directly exposed to moisture. Suitable connection accessories would be Elastomer sleeve 110mm, Elastomer end caps 110mm (if you do not need all inlets and outlets). As UV lamp we recommend our submersible UVC 40 W Amalgan or Immersion UVC 80 W Amalgam. Due to the use of deep well pumps, a flushing process is hardly audible. Additional options - different filter panels (filter mesh) in stainless steel RVS available to order and at extra cost in 43µ or 60µ (please note that with finer mesh the flow rate is 30% to 50% lower depending on the µ-thickness) - our EPS drum filters can be built individually on request according to drawings at an extra charge - individual biochambers (round or square) as well as trickle filters can be built on request in all sizes according to drawing - if you would like individual advice, please feel free to call us on 02945 / 96950 Functions of the control system: - Plug place for circulation and rinsing pump - plug and play via sensor with measuring pins  - automatic cleaning - Switch for on/off incl. emergency switch - Button for manual flushing - Flushing is triggered by probes (level of probes adjustable) - Rotation time/flush time adjustable - CE mark - detailed instructions for use are included - Cleaning is adjustable ( time and duration ) - Dry-running protection for the pond pump - Dry-running protection for circulation and flushing pump - Connections for sensor and safety switch Why EPS drum filters? after 30 years of experience and many purchased and self-tested filter systems from different suppliers, we decided to build our own drum filter series. There are stainless steel, PE and PP drum filters on the market. Some of the stainless steel filters were notable for their poor workmanship (cheap tank connectors that leaked, broke off or had rust defects). PE filters caused big problems when exposed to sunlight (bending and warping of the material) Many drum filters do not have a direct drive and are driven by pinions, V-belts or toothed belts. In our view, these are all weak points that can lead to malfunctions. For these reasons, we decided to build PP filters that do not deform, are acid-resistant and are operated with a direct drive. After an intensive test period of approx. 6 years in our own KOI facility, which consists of approx. 60 tanks of various sizes, with full fish stocking and abundant feeding every day, we started series production. All these problems are now a thing of the past - We love clear water and healthy fish EPS drum filters reduce the need for cleaning and maintenance in fish farms and garden ponds to a minimum. The processing is carried out using the latest technology such as CNC machines, which guarantees quality and precision. The systems can be used in the koi and/or swimming pond sector as well as in fish farming, industry and public areas.Dispatch by one-way pallet 220x100x80Technical data:EPS Combi Drum Filter CL65The new control system is preset ex works with a water-saving function, whereby the first contact at the probes causes the drum to rotate half a turn without flushing. At the second contact on the probes, the drum is rotated a full revolution and cleaned completely. This reduces electricity and water consumption. You can convince yourself of the quality at any time in our showroom We look forward to your visit

Function The function of the drum filter is to filter polluted water mechanically. Smallest particles are separated from the water by a stainless steel sieve RVS 316 of 75 micrometres and led to the outside via a dirt drain. This filtering process is automatically regulated by a control system and monitored by probes. In the event of a malfunction, the filter automatically switches off the circulation and backwash pump. The water level is constantly monitored by probes. The EPS Combi Drum Filter CL65 is made of very high quality PP plastic and is supplied including control, emergency cover switch, manual channel flushing, complete piping from the flushing pump to the flushing channel, level regulator, cover and built-in flushing pump in an unprecedented price/performance ratio. All inclusive. All EPS drum filters are reinforced with a 50/50 U-profile and an inner core of 40/40 4 Kant steel pipe. The direct drive from the motor to the drum means that there are no wear parts as with conventional drum filters (V-belts, toothed belts or plastic gears). If the dirty water channel should ever become clogged due to strong filamentous algae or leaves, it is no problem to simply dismantle and clean it without having to dismantle the filter drum or remove the mesh. In the integrated biochamber (102 x 98 x 97 cm) a Japanese air hose ( 19 mm ) is directly pre-installed for a better "moving bed" process for improved turbulence of the HX 13/17. This requires a diaphragm pump of 100-120 L/min. We recommend either HAP series, the Secoh series or the AP series. In addition, the biochamber has been equipped with 8 mm slots to insert HX13/17.  Please note the protected and unprotected surface of the HX13/17. According to this, the square metre of bacteria removal surface is calculated. The CL65 drum filter is available in both pump and gravity versions. Even if you have a gravity version, it is possible to convert it to a pump version in just a few steps (if you need help with this, we will be happy to assist you). Instructions for the conversion are enclosed with the control box. The fuse function or the emergency lid switch switches off the immersion UVCs directly when the lid is opened. The function is only guaranteed if they are connected via the supplied control unit. It is recommended that the electrical connection of the control unit is protected by a residual current circuit breaker. The control unit should not be directly exposed to moisture. Suitable connection accessories would be Elastomer sleeve 110mm, Elastomer end caps 110mm (if you do not need all inlets and outlets). As UV lamp we recommend our submersible UVC 40 W Amalgan or Immersion UVC 80 W Amalgam. Due to the use of deep well pumps, a flushing process is hardly audible. Additional options - different filter panels (filter mesh) in stainless steel RVS available to order and at extra cost in 43µ or 60µ (please note that with finer mesh the flow rate is 30% to 50% lower depending on the µ-thickness) - our EPS drum filters can be built individually on request according to drawings at an extra charge - individual biochambers (round or square) as well as trickle filters can be built on request in all sizes according to drawing - if you would like individual advice, please feel free to call us on 02945 / 96950 Functions of the control system: - Plug place for circulation and rinsing pump - plug and play via sensor with measuring pins  - automatic cleaning - Switch for on/off incl. emergency switch - Button for manual flushing - Flushing is triggered by probes (level of probes adjustable) - Rotation time/flush time adjustable - CE mark - detailed instructions for use are included - Cleaning is adjustable ( time and duration ) - Dry-running protection for the pond pump - Dry-running protection for circulation and flushing pump - Connections for sensor and safety switch Why EPS drum filters? after 30 years of experience and many purchased and self-tested filter systems from different suppliers, we decided to build our own drum filter series. There are stainless steel, PE and PP drum filters on the market. Some of the stainless steel filters were notable for their poor workmanship (cheap tank connectors that leaked, broke off or had rust defects). PE filters caused big problems when exposed to sunlight (bending and warping of the material) Many drum filters do not have a direct drive and are driven by pinions, V-belts or toothed belts. In our view, these are all weak points that can lead to malfunctions. For these reasons, we decided to build PP filters that do not deform, are acid-resistant and are operated with a direct drive. After an intensive test period of approx. 6 years in our own KOI facility, which consists of approx. 60 tanks of various sizes, with full fish stocking and abundant feeding every day, we started series production. All these problems are now a thing of the past - We love clear water and healthy fish EPS drum filters reduce the need for cleaning and maintenance in fish farms and garden ponds to a minimum. The processing is carried out using the latest technology such as CNC machines, which guarantees quality and precision. The systems can be used in the koi and/or swimming pond sector as well as in fish farming, industry and public areas.Dispatch by one-way pallet 220x100x80Technical data:EPS Combi Drum Filter CL65The new control system is preset ex works with a water-saving function, whereby the first contact at the probes causes the drum to rotate half a turn without flushing. At the second contact on the probes, the drum is rotated a full revolution and cleaned completely. This reduces electricity and water consumption. You can convince yourself of the quality at any time in our showroom We look forward to your visit