PVC adhesive cap 75 mm

Abbildung ähnlich

PVC fittings come from industrial plant construction and are characterised by their high pressure resistance (up to 16 bar). Pipe systems made with this system are also very durable and cost-effective. Fittings with a maximum pressure resistance of 10 bar are usually sufficient for ponds. Before you glue the pipes, however, you should observe the following instructions:

sand the bonding surfaces of the pipe parts to be joined with fine sandpaper.
then clean the bonding areas with our PVC cleaner to remove dust and grease.
apply the adhesive to the joint and allow it to flash off briefly.
Put the parts together and turn them a little.
after about 8 seconds it is no longer possible to change the connection!
observe the specified drying time of the adhesive before pressurising the pipe and allowing water to reach the glued joints.

Always carry out all work only in well-ventilated rooms and seal the adhesive and cleaner immediately after use! Make sure that adhesive and cleaner do not get on textiles, as adhesive is almost impossible to remove and cleaner can cause discolouration.

Material:	PVC
Size:	20 mm, 16 mm, 10 mm, 315 mm, 90 mm, 32 mm, 200 mm, 12 mm, 160 mm, 25 mm , 63 mm , 125 mm , 75 mm, 250 mm, 40 mm, 140 mm, 400 mm, 225 mm, 110 mm, 50 mm

Zubehör

PVC adhesive Tangit 125g tube

Litres: 125 ml

To make pressure-resistant connections, you need special glue which welds the plastic parts together. Please note that PE cannot be glued. Before you apply the adhesive, the bonding area must be cleaned free of dust and grease. However, with various liquids from the pharmacy, condensation remains due to the evaporation cold, so that the glue joint may be leaky. Therefore, always use special PVC cleaners.

Contenuto: 0.125 liter (76,00 €* / 1 liter)

9,50 €*

PVC adhesive Tangit 250ml / 240g with brush

Litres: 250 ml

To make pressure-resistant connections, you need special glue which welds the plastic parts together. Please note that PE cannot be glued. Before you apply the adhesive, the bonding area must be cleaned free of dust and grease. However, with various liquids from the pharmacy, condensation remains due to the evaporation cold, so that the adhesive joint may be leaky. Therefore, always use special PVC cleaners

Contenuto: 0.25 liter (51,80 €* / 1 liter)

Varianti da 9,50 €*

12,95 €*

PVC adhesive Tangit 500ml /480g with brush

Litres: 500 ml

To make pressure-resistant connections, you need special glue which welds the plastic parts together. Please note that PE cannot be glued. Before you apply the adhesive, the bonding area must be cleaned free of dust and grease. However, with various liquids from the pharmacy, condensation remains due to the evaporation cold, so that the adhesive joint may be leaky. Therefore, always use special PVC cleaners

Contenuto: 0.5 liter (47,90 €* / 1 liter)

Varianti da 9,50 €*

23,95 €*

PVC adhesive Tangit 1000 ml / 960 g with brush

Litres: 1000 ml

To make pressure-resistant connections, you need special glue which welds the plastic parts together. Please note that PE cannot be glued. Before you apply the adhesive, the bonding area must be cleaned free of dust and grease. However, with various liquids from the pharmacy, condensation remains due to the evaporation cold, so that the adhesive joint may be leaky. Therefore, always use special PVC cleaners

Varianti da 9,50 €*

34,95 €*

PVC cleaner 250 ml

Litres: 250 ml

Cleans thoroughly - Dust and grease-free. No condensation water remains! Before you apply a PVC adhesive (S3 or Tangit) to the PVC parts, the bonding area must be cleaned free of dust and grease. However, with various liquids from the pharmacy, condensation water remains due to the evaporation cold, so that the bonding point may be/become leaky. Therefore, always use special PVC cleaners

Contenuto: 0.25 liter (27,80 €* / 1 liter)

6,95 €*

PVC cleaner 1000 ml

Litres: 1000 ml

Varianti da 6,95 €*

10,50 €*